X-NPMI-R

RACK MOUNT PANEL FOR X-NPMI

X-NPMI-R

X-NPMI Configurable Network Paging Console

• 4.3-inch color LCD touch screen
• Intuitive and simple user interface
• Detachable gooseneck microphone
• Built-in monitor loudspeaker
• Digital audio processing
• Flush mount desktop installation available

X-NPMI Configurable Network Paging Console is a key module in X-618 Digital Public Address and
Voice Alarm System. It provides paging, monitoring, full duplex communication, touch screen operation and other configurable functions.

FEATURES

• CONNECTIONS
  • X-618 system can connect with up to 20 X-NPMI via Ethernet. X-NPMI can be used as a node anywhere in the network. To reduce wiring cost, the devices can be connected into an existing network provided that there is sufficient bandwidth to reduce wiring cost.
• AUDIO TRANSMISSION
  • The device comes with a detachable gooseneck microphone. Users can change different types of microphone for different real-time broadcasting requirements. The received audio signal will be digitalized to eliminate sound distortion during transmission.
  • The built-in speaker not only can be used for zone monitoring but also full-duplex intercom with other X-NPMI in the network.
  • X-NPMI supports fail-safe operation. Even when the connected X-DCS2000/EN fails, X-NPMI is still able to communicate with other X-NPMI and broadcast through other X-DCS2000/EN in the network.
• TOUCH SCREEN
  • Users can operate directly on the innovative 4.3-inch color LCD touch screen without adding an extra key module unit. With the touch screen, users can supervise the system status, select broadcast zones, assign zone groups or other broadcast controls, including setting playlists, timing roadcastings etc. With the built-in configuration software, zones broadcast status or button functions can be configured easily.
• SHORT-CUT OPERATION
  • X-NPMI has three short-cut buttons on the operation panel: microphone switch, all-zone emergency broadcast button can switch the system to emergency broadcast mode, where recorded evacuation message will be played and fire alarm will be activated without delay.

X-NPMS

Network Paging Console

X-NPMS

Configurable Network Paging Station

The X-NPMS connects to the X-618 system, transmitting audio and control signal through the Ethernet. It is used for live paging, audio task delivery , audio monitoring zones , and intercommunication.

FEATURES

• FUNCTIONS
  • Manual emergency broadcast
  • Normal broadcast control
  • Zoning and grouping broadcast
  • Monitoring function
  • Internal communication
  • Faults monitoring
  • Automatic record
  • Quick and simple broadcast
  • Recording audio in advance and broadcasting
  • Broadcasting the audio file of U-disk
  • Daily record
• TOUCH SCREEN
  • Users can operate directly on the innovative 7-inch color LCD touch screen without adding an extra key module unit.With the touch screen, users can supervise the system status, select broadcast zones, assign zone groups or other broadcast controls, including setting playlists, timing broadcastings etc.
  • With the built-in configuration software, zones broadcast status or button functions can be configured easily.
• CONNECTIONS
  • X-618 system can connect with up to 250 X-NPMS via Ethernet. X-NPMS can be used as a node anywhere in the network. To reduce wiring cost, the devices can be connected into an existing network provided that there is sufficient band width to reduce wiring cost.

X-ND100

Digital Noise Detector

X-ND100

X-ND100 (Digital Noise Detector) is used to detect ambient noise, automatically calculate the noise SPL, and transmit the SPL data to X-DCS3000. It is an important component to fulfill the function of automatic volume control. While broadcasting, the sound is mixed with ambient noise. In order to measure the noise SPL accurately, X-ND100 measures broadcast signal from speaker lines, comparing it with the broadcast signal from the microphone to get the actual noise data.

INSTALLATION NOTES

• Installation
  • Builders can conveniently install the noise detector into a hole with diameter of 160mm in the ceiling, and secure it with the spring clamps on both sides of the shell. Thickness of the ceiling is 5~25mm.
• Wiring
  • There are two terminals inside the noise detector. One is used to connect the control line for communication and power supply, and another is used to connect the speaker line. The polarity of wires shall conform to the marks beside the terminals. Generally, 0.75mm2 twisted wires are recommended. If the distance from the noise detector to controller exceeds 1000m, please use 1mm2 twisted wires.

FEATURES

• Connect to the X-DCS3000 by a pair of cables, to the communication and power terminals.
• Max. 5 noise detectors for each channel.
• Fire-proof ABS shell.
• Collects broadcast signals and noise signals.
• Max. transmission distance is 1000m.
• Flush-mounting in ceiling.
• Ideal for indoor installation.

X-DCS2000/EN

Digital Integrated System Manager 8

SX-DCS2000/EN

Highly integratedEasy-access preset buttonsBuilt-in fault diagnosisAutomatic volume controlExtendable zones connections via software configuration

DESCRIPTION

X-DCS2000/EN Digital Integrated System Manager (abbr. DCS) is the basic unit of X-618 Public Address and Voice Alarm System. DCS integrates plentiful functions such as zone expansion, multiple audio sources support, audio file storage, net audio, broadcasting, zone control, monitoring, fault diagnosis etc. The supplied X-SMART management software allows users to easily and efficiently manage and control the system.

FEATURES

• Input/ Output
  • DCS has 8 dry-contact outputs that can be used to activate external devices. It has 8 pairs of loudspeaker line output where each one allows multiple 100V loudspeakers to be connected in parallel. A record output port is dedicated for external recording.
  • DCS also has 8 dry-contact inputs that can be linked with a fire alarm control center which supports broadcasting alarm tones and evac- uation announcement when fire happens. On the rear panel, there are 4 network audio input and 4 auxiliary inputs, which provide con- nections to external audio sources such as CD/DVD, cassette, FM tun- er etc. In addition, there are 4 audio inputs that are capable to adjust volume automatically according to ambient noise (when HN-D32N Noise Detector is installed). Users can set the phantom power and input gain of each volume control input on the rear panel.
• Connections Expansion
  • DCS can connect with devices and the network to extend zone connections via 4 10M/100M adaptable Ethernet interfaces.
• Safety and Robustness
  • DCS can detect errors on main power supply, backup power supply, amplifier circuit, amplifier protection, software, communications, and loudspeaker line in runtime. By locating the error’s occurrence, DCS provides valuable information for repairing or replacing the malfunctioned devices.
  • DCS supports power supply and amplifier redundancy. Built-in fuse provides over-current protection to the main power supply. When a shortcircuit error is detected in DCS, the power supplied from main power will be cut off and switched to the backup one. Same technology is also used in amplifier switchover. User can configure the amplifier backup solution as 3 backup for 1 main, 2 backup for 1 main, 1 backup for 1 main or 2 backup for 2 main.
• Audio Storage
  • DCS is built with a 1GB flash memory. Via X-618 Config software, users can upload audio files for later playback or audio synthesis. Volume controllers can be connect- ed with the DCS contact outputs to adjust the zones volume or force switching.

X-DCS3000

X-DCS3000 Digital Integrated System Manager

X-DCS3000

X-DCS3000 Digital Integrated System Manager (abbr. DCS) is the basic unit of X-618 Public

Address and Voice Alarm System. DCS integrates plentiful functions such as zone expansion, multiple
audio sources support, audio file storage, net audio, broadcasting, zone control, monitoring, fault diagnosis etc. With powerful audio matrix structure, X-DCS3000 is capable of bringing value to big infrastructures in terms of saving extension and cabling.

FEATURES

• INPUT/OUTPUT
  • DCS can connect up to 8 amplifier channels and support 4 x 8 audio matrix for both local audio input and network audio routing.
  • DCS has 8 dry-contact outputs that can be used to activate external devices. It has 8 pairs of loudspeaker line output where each one allows multiple 100V loudspeakers to be connected in parallel. A record output port is dedicated for external recording.
  • DCS also has 8 dry-contact inputs that can be linked with a fire alarm control center which supports broadcasting alarm tones and evacuation announcement when fire happens. On the rear panel, there are 4 network A/D audio input, which provide connections to external audio sources such as CD/DVD, cassette, FM tuner etc. With addition X-ND100 Noise Detector, AVC (Automatic Volume Control) function can be active Users can set the phantom power and input gain of each volume control input on the rear panel.
• CONNECTIONS EXPANSIONN
  • DCS can connect with devices and the network to extend zone connections via 4 10M/100M adaptable Ethernet interfaces.
• SAFETY AND ROBUSTNESS
  • DCS can detect errors on main power supply, backup power supply, amplifier circuit, amplifier protection, software, communications, and loudspeaker line in runtime. By locating the error’s occurrence, DCS provides valuable information for repairing or replacing the malfunctioned devices.
  • DCS supports power supply and amplifier redundancy. Built-in fuse provides over-current protection to the main power supply. When a short-circuit error is detected in
  • DCS, the power supplied from main power will be cut off and switched to the backup one. DCS has two backup amplifier channel to standby for 8 main amplifier channel. It is configurable for backup strategy by config software.
• AUDIO STORAGE
  • DCS is built with flash memory which can store up to 60 minutes voice message. Via X-618 Config software, users can upload audio files for later playback or audio synthesis. Volume controllers can be connected with the
  • DCS contact outputs to adjust the zones volume or force switching.
• BROADCASTING
  • DCS supports a variable range of audio sources, such as audio files from external devices (CD/DVD, cassette, FM tuner and etc.), remote paging announcement or broadcasting from X-NPMI/X-NPMS, etc.
  • DCS can broadcast 4 audio message or internet audio simultaneously. Timer broadcast setting can be configured via software to allow system to play specific programs at a specific time even when it is not supervised. With the software, user can also handle up to 255 priorities to meet complex public address requirements.
• COMPONENTS
  • Buttons for special operations: select all, reset, error confirm and etc.
  • Zone selection buttons
  • Audio source selection buttons
  • Emergency mode button
• INDICATORS
  • Device status indicator lights can show whether the device is powered, malfunctioned, disabled, running or delayed
  • Zone status indicator lights
  • Audio source status indicator lights
• INTERFACES
  • 8 dry-contact outputs
  • 8 loudspeaker line outputs
  • 8 dry-contact inputs
  • 8 DCL inputs
  • 8 amplifier interfaces
  • RS – 485 port for fire alarm
  • Main power port
  • Backup power port (DC 24V)
  • 4 10/100M adaptable Ethernet interfaces

Certification and Standard
Category Region Certification
Safety Europe CE Complied