Search for:
JT-PWDUEL

POWER SUPPLY-SWITCHING TYPE 110V/220V FOR IP-AK2 & PRO3000


FEATURES & SPECIFICATIONS

  • To charge lead acid battery
  • Auto switch when power off (UPS function)
  • AC mains failure signal
  • Battery low signal
  •  Protections: overload/ over voltage/short circuit
  •  Dimension: 111 × 78 × 36(mm)
  • AC input voltage range: 85~264 VAC (120~370 VDC Input)
  • Frequency: 47~63Hz
  • Inrush current: cold start, 15A/115V, 30A/230V
  • Input leakage current: <1mA/ 230VAC
  • Line regulation (full load): ≤±0.5%
  • Output voltage adjust range: V1: ±5% of rated output voltage , V2: unadjustable
  • Output overload protection: built-in IC protection, hiccup mode, auto recovery
  • Output over voltage protection: 115~150%, hiccup mode, auto recovery
  • Withstand voltage: I/P -O/P: 3.0KVAC/1min, I/P -F/G: 1.5KVAC/1min, O/P-F/G: 0.5KVAC/1min
  • Rise time: 50ms@full load (typical)
  • Hold up time: 20ms@full load (typical)
  • Operating temperature: -20°C~+50°C
S-4
Honeywell Assy, 30vdc Suppressor, Wire Leads
S-4

The Honeywell Access S-4 is a surge supressor used with Honeywell’s N-1000-II, N-1000-III, N-1000-IV, NS2 and NS2+ access control panels. The supressor protects the panel against electrical spikes caused by excess energy from collasping electrical fields that could potentially damage the device. The supressor is connected through a relay contact included on the panel.

FEATURES
  • Compatible with Honeywell N-1000-II, N-1000-III, N-1000-IV, NS2 and NS2+ access control panels

EXB-1
EXIT BUTTONPT SINGLE GANG PLASTIC MOUNTI
EXB-1

EXB-1 exit buttons with single-gang stainless steel mounting plates feature DPDT switch configuration. These buttons can be configured with momentary or latching contact status.

PRO32E1PS
Honeywell ACCESS PSU Assembly 4A for Pro2200 Sys
PRO32E1PS

The PRO32E1PS and PW6K2E2PS power supply and battery charger is compatible with the PW3000,PW5000, PW6000, PRO2200, and PRO3200 systems. For ordering purposes please use the PW6K2E2PSfor the PW3000, PW5000, and PW6000 systems and PRO32E1PS for PRO2200, and PRO3200 systems.This power supply will convert AC input voltage into a 13.8VDC output with 4.0 amps maximum of continuous current. The power supply accepts an input voltage of 85VAC to 265VAC at 50Hz/60Hz. The power supply provides AC fail and low battery supervision when connected to PW3000, PW5000,PW6000, PRO2200, and PRO3200 I/O PFL (Power Fail) and auxiliary inputs.

FEATURES
  • 4.0 amp maximum continuous output current at 13.8VDC with overload protection
  • Filtered and electronically regulated outputs
  • Built-in charger for sealed lead acid batteries with a maximum charge current of 250mA
  • Automatic switch over to stand-by battery, if present, upon AC power failure
  • Reverse battery polarity with a non-replaceable fuse
  • Low battery supervision when connected to a low battery input on the panel
  • AC fail supervision when connected to PWR fail on panel
  • Short circuit/overload/overvoltage protection
  • 0° C to 49° C operating temperature range
  • UL 60950 listed
  • CE compliant

PRO22DCC
CABLE DATA DAISY CHAIN CBL
PRO22DCC

Honeywell Access PRO22DCC Daisy Chain Cable